D:\Portable\AMDFLASH>amdvbflash.exe /?
--- amdvbflash v2.93 ---
-h, -?, /h, /? Help (this screen)
Format: amdvbflash [command] [parameter1] [parameter2] [parameter3] <option/s>
[command]:
-i [Num] Display information of AMD adapters in the system.
Display information of adapter [Num] if specified.
-ai [Num] Display advanced information of AMD adapters on system.
Display advanced information of adapter [Num]
if specified.
-biosfileinfo <File> Displays the Bios info in file <file>
-p <Num> <File> Write BIOS image in file <File> to flash ROM in Adapter
<Num>.
-pa [-padevid=] <File> Write BIOS image <File> to all appropriate adapters.
Use with -padevid or -passid or -pasvid or -pavbpn or -f
p.
Command example:
command = -pa -padevid=0xXXXX a123.bin
-s <Num> <File> [Size] Save BIOS image from adapter <Num> to file <File>.
First [Size] kbytes (except for Theater in bytes) of ROM
content is saved if [Size] is specified.
-cf <File> [Sum] Calculate 16-bit checksum for file <File>.
Checksum for the file is compared to [Sum] which is
the expected checksum
-cb <Num> [Sum] Calculate 16-bit BIOS image checksum for adapter <Num>.
Checksum for the BIOS image is compared to [Sum] which i
s
the expected checksum
press any key to continue
-cr <Num> [Size] [Sum] Calculate 16-bit ROM checksum for adapter <Num> and
compare it to the [Sum] specified. This command is
the same as -cb if [Size] is specified.
-t <Num> Test ROM access of adapter <Num>
-v <Num> <File> Compare ROM content of adapter <Num> to <File>
-mi <Num> [ID] Modify SSID & SVID in BIOS image of adapter <Num> to
<ID>. SSID & SVID in BIOS image of adapter <Num> is
displayed if [ID] is not specified.
-mb <Num> <File> Modify SSID, SVID, BIOS Pin Number, & Boot Message in
BIOS image of adapter <Num> to values in <filename>.
Input file example:
ssid = 715B
svid = 1002
biospn = "113-xxxxxx-xx"
bootmsg = "AMD graphic board"
-pak <File> Package an executable for BIOS update according to
the commands in <File>.
Config file example:
outfile = update.exe
banner = "Update v1.0"
infile = a123.bin
command = -pa -padevid=715B infile
-isr <Num> <Build Number> <Board Number> Set ISR number based on the given
build and board number
if not specified, print out ISR Number
-prod <Num> <12 digit serial number> Set PROD number based
on the given serial number
if not specified, print out SN Number
-checkprodsn <Num> <12 Digit Serial Number> Comparing the Prod SN based on
existing prod sn saved in ROM
press any key to continue
<option/s>:
-f Force flashing regardless of security checkings (e.g. AsicID &
BIOS file info check OR boot-up card).
-fa Force flashing bypassing already-programmed check.
-fm Force flashing bypassing BIOS memory config check.
-fs Force flashing bypassing BIOS SSID check.
-fp Force flashing bypassing BIOS P/N check.
-sst Use SST25VFxxx flashing algorithm regardless of ROMID straps.
-st Use ST M25Pxx flashing algorithm regardless of ROMID straps.
-atmel Use AT25Fxxx flashing algorithm regardless of ROMID straps.
-keepisrsn keep the ISR Number on the adapter when flashing a new VBIOS
-keepprodsn keep the Prod SN on the adapter when flashing a new VBIOS
press any key to continue
-siireset Specifies the GPIO Pin to be used as the Reset when updating
SiI1930 microcontroller firmware
Input example:
-siireset=7 <No Spaces>
-siiuprog Specifies the GPIO Pin to be used as the uprog when updating
SiI1930 microcontroller firmware
Input example:
-siiuprog=14 <No Spaces>
-scansii Overrides normal adapter detection to enable detecting SSI
roms with/without TPI firmware
-log Logs output to amdvbflash.log, overrides existing file
-logappend Logs and appends output to amdvbflash.log
-ddc Enable DDC support
-padevid=<ID> Use with -pa command to update adapters of specific device ID.
-passid=<ID> Use with -pa command to update adapters of specific SSID.
-pasvid=<ID> Use with -pa command to update adapters of specific SVID.
-pavbpn=<VBPN> Use with -pa command to update adapters of specific VBIOS PN.
press any key to continue
-excl_memtrain_dtable When flashing on new VBIOS, a pre-determined memory
training data table in the old VBIOS will not be
overwritten.
-isr <adapter num> [build num] [board num] If build number and board number
are specified, sets the ISR Numbe
r
value in specified adapter.
If only adapter is specified, the
current
ISR Number is displayed
-checkpn <adapter num> <filename> Checks PN of the current product
and compares it to external file
-rsa <filename> Verify VBIOS immage file RSA sign
ature
*<Num> = adapter number, <File> = filename
*[Size] = data block size in KBytes, except for Theater Pro in Bytes
*Use command -i to see the adapter numbers in the system.